FOCUS ON YOUR ENTRUST

FOCUS ON YOUR ENTRUST

The high-quality TECHNOBELT (Neoprene and Polyurethane Belt) has won high praise from many famous original equipment manufacturers and maintenance companies all over the world.

View details
FOCUS ON YOUR ENTRUST

FOCUS ON YOUR ENTRUST

The high-quality TECHNOBELT (Neoprene and Polyurethane Belt) has won high praise from many famous original equipment manufacturers and maintenance companies all over the world.

View details

Features of Endless Conveyor Belt

The endless conveyor belt means that the conveyor belt has been made into an endless conveyor belt without joints in the production process. The strength of the belt core joint can reach 90% of the strength of the belt body. There is no obvious joint defect on the surface of the belt. long and small. The belt core of the endless conveyor belt is made of high-quality cotton or dimensional cotton interwoven canvas, generally 2-6 layers or NN-200 nylon canvas (or polyester canvas) as the strength layer.

The length of the endless conveyor belt and the limit deviation: the length of the endless conveyor belt is m, the limit deviation is mm, the length is less than 15 ± 50, the length is 15-20 ± 75, the length is greater than 20, and the belt length is ± 0.5%. The company can produce suitable length, width and thickness according to customer needs. Common type, heat-resistant type (≤120℃), cold-resistant type (not lower than -40℃), acid and alkali resistant type, high temperature resistant type (not higher than 150℃) and sanitary annular conveyor belt.

 

Length and limit deviation of endless conveyor belt:

Endless conveyor belt length m         Limit deviation mm

length less than 15                       ± 50

Length 15-20                           ± 75

Length greater than 20                   ± 0.5%

图片名称

Industrial Timing Belt Knowledge

26 Aug,2020

Industrial Timing Belt Knowledge Classification of Industrial Timing Belts

MORE
图片名称

Correct Use of Timing Belt

24 Aug,2020

Correct Use of Timing Belt

MORE
图片名称

Common Faults and Solutions for V Belts

14 Aug,2020

A: There is noise: the tension is too large or too small, the solution: the tension should be adjusted. B: Edge wear: 1) Timing belt incident is not parallel 2) Timing belt wheel steering deflection 3) Rising pulley has cracks 4) Bearing has gaps Solution: 1)  Straighten the non-parallel synchronous belt wheels and replace the synchronous belt. 2) Replace the tensioner, suspension wheel and timing belt C: Wear of the surface fabric at the root of the convex tooth (1) Excessive tension (2) Excessive temperature (3) Damage to the synchronous pulley. Solution: (1) Adjust the tension (2) Find the cause of the high temperature and repair it (3) Replace the synchronous pulley D: The flanks of the convex teeth are abnormally worn, the bottom is cracked, and the convex teeth are cut: (1) The tightening force is too large or too small (2) There is foreign body (3) The timing belt pulley or the tension pulley is seized. Solution: (1) Adjust the tension (2) Remove foreign objects (3) Find the cause and repair E: The volume of the surface fabric of the convex teeth: the engine or other parts have liquid leakage. Solution: repair the leaking parts and replace the timing belt F: Movement scratches on the convex teeth: (1) Foreign matter (2) The timing belt is damaged before or during installation Solution: (1) Remove foreign objects (2) Replace the timing belt and install it correctly G: Cracks appear on the back of the synchronous belt: (1) The surrounding temperature is too high or too low (2) There is foreign matter (3) The suspension wheel is sticky (4) Aging Solution: (1) Find the cause and solve it (2) Replace the timing belt and check the door cover (3) Replace the idler wheel and timing belt (4) Replace the timing belt H: The timing belt suddenly breaks: (1) There is a foreign body (2) The tension is too large (3) The timing belt is improperly bent before installation Solution: (1) Remove foreign matter (2) Adjust the tension (3) Replace the timing belt I: Related parts are damaged: (1) There is a gap in the bearing (2) The moving contact surface is damaged Solution: (1) Replace the tensioner, idler and guide wheel

MORE
< 1...828384...90 >

Messages

SUBMIT

Quick Link

Contact Us

DALIAN TECH MACHINERY CO.LTD

Address：No.13 Ganjingzi District, Dalian,   Liaoning  province, China

TEL/WhatsApp：+86-15942618996

                                +86-15566858562

Email：sales@maxpowergroup.cn

Copyright © DALIAN TECH MACHINERY CO.LTD

Powered by: 300.cn  dalian    SEO   Business License