FOCUS ON YOUR ENTRUST

FOCUS ON YOUR ENTRUST

The high-quality TECHNOBELT (Neoprene and Polyurethane Belt) has won high praise from many famous original equipment manufacturers and maintenance companies all over the world.

View details
FOCUS ON YOUR ENTRUST

FOCUS ON YOUR ENTRUST

The high-quality TECHNOBELT (Neoprene and Polyurethane Belt) has won high praise from many famous original equipment manufacturers and maintenance companies all over the world.

View details

Slippage and Solutions of PVC Conveyor Belt

There are many reasons for the slippage of the conveyor belt during operation. The common reasons and solutions are:

1. The initial tension is too small. Insufficient tension at the point where the conveyor belt leaves the drum causes the conveyor belt to slip. This situation generally occurs at startup, and the solution is to adjust the tensioning device and increase the initial tension.

2. Too fast startup speed can also cause slippage. At this time, it can be started slowly, and it can be started after jogging twice, which can also effectively overcome the slippage.

3. The rear roller bearing is damaged and cannot rotate or the upper and lower idler bearings are damaged and cannot rotate too much. The reason for the damage is that the tail floats too much, and the damaged or inflexible parts are not repaired and replaced in time, which increases the resistance and causes slippage.

4. The friction between the drive roller and the conveyor belt is not enough to cause slippage. The main reason is that there is water on the conveyor belt or the environment is wet. The solution is to add some rosin powder to the roller. But be careful not to add it by hand, but blow it in with a blower device to avoid personal accidents.

5. The load of the conveyor belt is too large, and it will slip if it exceeds the capacity of the motor. The advantage of slippage at this time is that it protects the motor. Otherwise, the motor will be burned for a long time. But for operation, it is a slip accident.

图片名称

Industrial Timing Belt Knowledge

26 Aug,2020

Industrial Timing Belt Knowledge Classification of Industrial Timing Belts

MORE
图片名称

Correct Use of Timing Belt

24 Aug,2020

Correct Use of Timing Belt

MORE
图片名称

Common Faults and Solutions for V Belts

14 Aug,2020

A: There is noise: the tension is too large or too small, the solution: the tension should be adjusted. B: Edge wear: 1) Timing belt incident is not parallel 2) Timing belt wheel steering deflection 3) Rising pulley has cracks 4) Bearing has gaps Solution: 1)  Straighten the non-parallel synchronous belt wheels and replace the synchronous belt. 2) Replace the tensioner, suspension wheel and timing belt C: Wear of the surface fabric at the root of the convex tooth (1) Excessive tension (2) Excessive temperature (3) Damage to the synchronous pulley. Solution: (1) Adjust the tension (2) Find the cause of the high temperature and repair it (3) Replace the synchronous pulley D: The flanks of the convex teeth are abnormally worn, the bottom is cracked, and the convex teeth are cut: (1) The tightening force is too large or too small (2) There is foreign body (3) The timing belt pulley or the tension pulley is seized. Solution: (1) Adjust the tension (2) Remove foreign objects (3) Find the cause and repair E: The volume of the surface fabric of the convex teeth: the engine or other parts have liquid leakage. Solution: repair the leaking parts and replace the timing belt F: Movement scratches on the convex teeth: (1) Foreign matter (2) The timing belt is damaged before or during installation Solution: (1) Remove foreign objects (2) Replace the timing belt and install it correctly G: Cracks appear on the back of the synchronous belt: (1) The surrounding temperature is too high or too low (2) There is foreign matter (3) The suspension wheel is sticky (4) Aging Solution: (1) Find the cause and solve it (2) Replace the timing belt and check the door cover (3) Replace the idler wheel and timing belt (4) Replace the timing belt H: The timing belt suddenly breaks: (1) There is a foreign body (2) The tension is too large (3) The timing belt is improperly bent before installation Solution: (1) Remove foreign matter (2) Adjust the tension (3) Replace the timing belt I: Related parts are damaged: (1) There is a gap in the bearing (2) The moving contact surface is damaged Solution: (1) Replace the tensioner, idler and guide wheel

MORE
< 1...828384...90 >

Messages

SUBMIT

Quick Link

Contact Us

DALIAN TECH MACHINERY CO.LTD

Address：No.13 Ganjingzi District, Dalian,   Liaoning  province, China

TEL/WhatsApp：+86-15942618996

                                +86-15566858562

Email：sales@maxpowergroup.cn

Copyright © DALIAN TECH MACHINERY CO.LTD

Powered by: 300.cn  dalian    SEO   Business License